A video claiming that Canon's "$18M stamp" makes ASML's "$180M machine look ancient" has pulled in more than 200,000 views in under a week. The machine behind it is real, but it is not new: Canon launched the FPA-1200NZ2C nanoimprint lithography system on 13 October 2023. What is worth understanding is how it prints chip patterns without the light source that makes EUV so expensive, and how far it really is from volume production. Here is the plain explanation, using Canon's official specifications.
What is nanoimprint lithography?
Every chip is built up layer by layer, and each layer needs a pattern transferred onto a light-sensitive resist on the wafer. Conventional photolithography does this like a slide projector: light shines through a mask, lenses or mirrors shrink the image, and it is exposed onto the resist. Nanoimprint lithography (NIL) does it like a rubber stamp. A mask with the circuit pattern carved into its surface is pressed directly into liquid resist on the wafer, the resist is hardened, and the mask is lifted off, leaving the pattern behind.
Because the pattern is transferred mechanically rather than through an optical system, Canon says fine features on the mask are reproduced faithfully on the wafer, and complex two- or three-dimensional shapes can be formed in a single imprint.
How Canon's NIL process works
- Dispense: an inkjet head places tiny droplets of resist exactly where the pattern needs material.
- Imprint: the patterned mask is lowered and pressed into the droplets, which flow into its trenches.
- Cure: the resist is hardened (with ordinary UV curing light, not a special patterning light source).
- Separate: the mask is lifted away and the next field is imprinted, step by step across the 300 mm wafer.
Alignment between layers, called overlay, is the hard part. Canon also had to develop environment control to keep fine particles out, because a single particle trapped between mask and wafer becomes a defect.
Canon FPA-1200NZ2C specifications
- Minimum linewidth: 14 nm, which Canon says is equivalent to the 5 nm node; with better masks it expects 10 nm, equivalent to the 2 nm node
- Overlay accuracy: 4 nm or better
- Field size: 26 x 33 mm, mask size 6 inch, wafer size 300 mm
- Main body: 2,700 x 6,600 x 2,830 mm (two stations)
- Other uses: metalenses for XR headsets and other optical microstructures, not only logic chips
Nanoimprint vs EUV: the key differences
- How the pattern is made: EUV projects 13.5 nm extreme ultraviolet light through a train of precision mirrors. NIL presses a 1:1 mask into resist, with no projection optics.
- Light source: EUV light comes from tin droplets blasted by a high-power laser, which is a large part of the cost and power bill. NIL needs no special-wavelength light source, which is why Canon says it can cut power consumption significantly compared with the most advanced photolithography for 5 nm-class chips.
- Cost claims: Canon chairman Fujio Mitarai said in 2023 that NIL tools would cost a digit less than EUV scanners. Figures such as "$18M vs $180M", "87% less energy" and "23% lower wafer cost" are Canon estimates under specific conditions, not measured results from a production fab.
- Masks: EUV masks are 4x larger than the printed pattern. NIL masks are 1:1 and touch the resist, so they must be made at full resolution and they wear, which is why NIL relies on replica masks made from a master.
- Maturity: EUV runs in high-volume fabs at TSMC, Samsung and Intel. Canon has not published a production throughput figure for NIL.
Where it stands today
- 13 October 2023: FPA-1200NZ2C launched.
- 26 September 2024: first announced shipment, to the Texas Institute for Electronics, a University of Texas-backed consortium, for research and prototyping.
- June 2026: an additional system shipped to a customer that is already evaluating NIL. With its third-quarter 2026 results, Canon said start-up of that unit is complete, process checks on customer wafers are going well, and it is now verifying NIL for production-line use, targeting mass-production adoption from 2027.
So NIL is not replacing EUV today. No customer has announced volume production on it, and defects, throughput and mask life are the questions it still has to answer. What makes it interesting is that it attacks the cost of patterning with a different physics instead of more expensive light, and Canon has already adapted the same stamping idea into a wafer planarisation process it aims to sell from 2027. For background on why lithography tools matter so much to chip supply, see our report on ASML equipment for India's Dholera fab.
Image credit: Canon Inc., FPA-1200NZ2C in operation (press image), resized.
About the author: Aswinth Raj is an electronics engineer and the editor of CircuitDigest, where he has published more than 150 hands-on projects and tutorials across Arduino, PIC, ESP32, Raspberry Pi and EV battery systems. He selects the stories on this page for what engineers and makers can actually learn or build from. Connect on LinkedIn
Add a comment
No account needed. Your comment appears once a moderator has reviewed it.