Bluetooth has always been able to tell you roughly whether a device is near or far by looking at signal strength. It has never been good at telling you how far. Bluetooth Channel Sounding, added in Bluetooth Core Specification 6.0 in September 2024, changes that. A new prototype called Free Ranger, built by Tomorrow Lab on NXP's MCX W72, shows what it looks like in practice: a handheld puck whose LED rings grow brighter as you get closer to a friend's device, with no map, compass or GPS.
What is Bluetooth Channel Sounding?
Channel Sounding (CS) lets two connected Bluetooth LE devices measure the actual distance between them. Before it, the only standard method was RSSI, the received signal strength. RSSI changes a lot when a hand covers the antenna, a body gets in the way or a signal bounces off a wall, so it gives a rough proximity zone at best. CS measures the radio signal's travel time and phase instead, which is far less sensitive to how strong the signal happens to be.
How Channel Sounding works
One device acts as the initiator and the other as the reflector. They hop across up to 72 channels, each 1 MHz wide, in the 2.4 GHz band, following a randomised sequence. Two measurements are combined:
- Round-trip time (RTT): the initiator sends a sync packet, the reflector replies after a known delay, and the time of flight gives distance. It is coarse, on the order of 30 cm resolution, but it is unambiguous and resists multipath because the first arrival wins.
- Phase-based ranging (PBR): both sides exchange pure tones on many channels and record the phase as IQ data. Phase changes linearly with frequency, and the slope of that line gives distance. PBR can be precise to centimetres, but the answer repeats roughly every 37.5 cm, so RTT is used to pick the right one.
The specification defines four step modes: Mode 0 for calibration, Mode 1 for RTT only, Mode 2 for PBR only, and Mode 3 for RTT and PBR in the same step. Mode 3 support is optional. The random hopping also makes relay attacks harder, which is why car makers want CS for keyless entry.
How accurate is it?
It depends heavily on antennas and surroundings. The Bluetooth SIG's target is around 0.5 m in most scenarios. TI's CC2755 smart lock demo reached under 50 cm accuracy over a 30 to 40 m range, and Silicon Labs found that using two antennas on each side, for four antenna paths, keeps most readings within 1 m. Real streets are harsher: an independent outdoor test of nRF54L15 boards measured 2 to 3 m RMS error on a busy street between 3 and 10 m, even after near-perfect results in clear line of sight. Expect room-level precision, not tape-measure precision, unless you invest in antenna design and filtering.
Which chips support Channel Sounding?
- NXP MCX W72: used in Free Ranger on the dedicated MCXW72-LOC board; the cheaper FRDM-MCXW72 board also supports CS with lower localisation performance.
- TI CC2755 (CC27xx family): includes an algorithm processing unit and an NPU for CS post-processing; TI says it was the first CS-certified wireless MCU in mass production.
- Silicon Labs EFR32xG24: Bluetooth 6.0 certified, with a dual-antenna CS dev board.
- Nordic nRF54L15: CS supported in Nordic's SDK, with a DK and a small tag board.
Who it suits
Channel Sounding suits item finders, smart locks, car keys, asset tracking and "find my friend" style gadgets where knowing the distance within a metre is enough. Both ends must support CS, so it will not work with older Bluetooth devices. Most of the effort is in the post-processing that turns raw IQ and timing data into a stable distance. If you are new to Bluetooth LE, start with our BLE proximity control project with ESP32, which uses the older RSSI method, and you will quickly see why CS matters.
Image credit: Tomorrow Lab / Potentially Genius, frame from the Free Ranger video, cropped and resized.
About the author: Aswinth Raj is an electronics engineer and the editor of CircuitDigest, where he has published more than 150 hands-on projects and tutorials across Arduino, PIC, ESP32, Raspberry Pi and EV battery systems. He selects the stories on this page for what engineers and makers can actually learn or build from. Connect on LinkedIn
Add a comment
No account needed. Your comment appears once a moderator has reviewed it.