Simple Two Way Intercom Circuit

Published  January 26, 2018   13

Author

Most of the schools and offices have intercoms to communicate with people inside a building or a particular campus. These are just like landline phones but, you do not need an operator, the voice received from one end will be directly transferred to the receiver on the other end.  In this circuit we are going to build a very Simple Intercom Circuit using which you can communicate two ways locally within your house or school. This project brings in the childhood memory of using matchboxes with thread to build a simple telephone. So now let’s take it to the next level by building an electronic circuit (amplifier) to transmit voice from one end to another end.

Materials Required:

1. LM386 Audio Amplifier
2. Speaker (2Nos)
3. Microphone (2Nos)
4. Resistors (10k, 4.7k, 10k)
5. Capacitor (0.1uf, 0.1uf, 10uf, 10uf)
6. SPDT switch

Circuit Diagram and Explanation:

The complete circuit diagram of this Intercom Project is given below.

As you can see the circuit is very simple and can be easily built over a breadboard. The main concept behind the circuit is the use of LM386 audio amplifier which receives the audio signal from microphone, amplifies it and plays it on the speaker. The LM386 has a gain range from 20-200; by default the value of gain is 20 but can be increased upto 200 by using a capacitor across the pins 1 and 8. Here we have used a capacitor of 10uF to get the maximum gain of 200. The resistor R2 is used to control the volume of the speaker; here I have limited the volume to medium level using a 4.7K resistor. You can experiment with values from 1k-100k to get the volume of your choice.

The output of the amplifier (pin 5) is connected to both the speakers. One speaker will be used in set-1 and the other in set-2 as show in the circuit diagram. The input of the amplifier is the microphone (microphone has polarity so be careful while connecting it), We cannot amplify the sound from both the microphone at the same time, so we use a SPDT (single pole double throw) switch as shown above.

The SPDT switch will connect only one microphone to the amplifier at a time. So only one person can talk at a time, this type of communication is called half-duplex communication and this is what we see in walki-talkies. Each time after speaking something the user has to flip this SPDT switch for the person on other end to start talking.

Working of Intercom Circuit:

Follow the circuit diagram above and make the connections. To make the project more attractive you can use long wires to increase the distance between the set-1 and set-2 microphone and speaker. You can use any normal wire for a decent length, but if you need cover higher distance use a twisted pair cable like CAT5 to avoid being affected by noise. I just used a normal wire for demonstration and the set-up looks something like this below:

The complete circuit is built on a bread board, and is powered by a 9V battery. The circuit can also run on voltage between 5V to 12V so choose a power supply which you are comfortable with. Now place the SPDT switch in a position and speak into the respective microphone your voice should be echoed on both the speakers. Similarly place the switch in opposite position and talk into the other microphone and check if you can hear the sound on the speakers. Initially you can experiment with the circuit by blowing air into the microphone and check if the speaker produces some noise.

You can also upgrade this project by adding another SPDT switch to turn of the speaker on your side when you are talking. Right now both the speakers will always be active to keep things simple, so do not worry if you hear yourself on the speaker on your end.

The complete working of the project is shown in the video below; you can also go through it if you are confused on how to use it. Hope you understood the project and got it working, if not feel free to use the comment section or the forums to post your doubt and I will try my best to resolve it.

Video

Submitted by Farazdeq on Mon, 01/29/2018 - 18:28

Good project

Good project

Submitted by yalpu on Tue, 03/20/2018 - 13:17

How much supply vtg to give

How much supply vtg to give for the circuit

Submitted by musa on Tue, 03/27/2018 - 21:28

two way intercom

I need literature review for this project pls

Submitted by Amir Ansari on Sun, 04/01/2018 - 14:19

Changing of supply voltage.

How to change possitive supply to negative supply. Simple way needed.

Submitted by Rajat on Mon, 04/02/2018 - 21:08

if u notice properly the

if u notice properly the output pin should be 6 not 5.

Submitted by Agustin Yanti on Mon, 04/23/2018 - 19:00

hi I'm Agustin from Indonesia

Submitted by Harikrishna on Thu, 04/26/2018 - 07:37

The circuit is not working.

The circuit is not working. Circuit diagram and the photograph you kept are different in connections.

Submitted by SURESH K. GOVIND on Tue, 05/08/2018 - 13:39

with the help of the SPDT

with the help of the SPDT switch, any one microphone will be active. thats ok. But, will the sound of the person (of any microphone) be heard in both speakers? i found the connection of the speakers are originated from the same