Color Detector using Arduino Uno

Published  October 18, 2015   50
Dilip Raja
Author
Color Detector using Arduino

In this project we are going to interface TCS3200 color sensor with Arduino UNO. TCS3200 is a color sensor which can detect any number of colors with right programming. TCS3200 contains RGB (Red Green Blue) arrays. As shown in figure on microscopic level one can see the square boxes inside the eye on sensor. These square boxes are arrays of RGB matrix. Each of these boxes contain Three sensors, One is for sensing RED light intensity, One is for sensing GREEN light intensity and the last in for sensing BLUE light intensity.

TCS230 Color Sensor Pinout

Each of sensor arrays in these three arrays are selected separately depending on requirement. Hence it is known as programmable sensor. The module can be featured to sense the particular color and to leave the others. It contains filters for that selection purpose. There is forth mode that is no filter mode. With no filter mode the sensor detects white light.

 

Components Required

Hardware: ARDUINO UNO, power supply (5v), LED, JHD_162ALCD (16*2LCD),TCS3200 color sensor.

Software: ARDUINO IDE (ARDUINO nightly).

 

Circuit Diagram and Working Explanation

In 16x2 LCD there are 16 pins over all if there is a back light, if there is no back light there will be 14 pins. One can power or leave the back light pins. Now in the 14 pins there are 8 data pins (7-14 or D0-D7), 2 power supply pins (1&2 or VSS&VDD or GND&+5v), 3rd pin for contrast control (VEE-controls how thick the characters should be shown), and 3 control pins (RS&RW&E)

 

In the circuit, you can observe I have only took two control pins. The contrast bit and READ/WRITE are not often used so they can be shorted to ground. This puts LCD in highest contrast and read mode. We just need to control ENABLE and RS pins to send characters and data accordingly. [Also check: LCD interfacing with Arduino Uno]

 

The connections which are done for LCD are given below:

PIN1 or VSS to ground

PIN2 or VDD or VCC to +5v power

PIN3 or VEE to ground (gives maximum contrast best for a beginner)

PIN4 or RS (Register Selection) to PIN8 of ARDUINO UNO

PIN5 or RW (Read/Write) to ground (puts LCD in read mode eases the communication for user)

PIN6 or E (Enable) toPIN9 of ARDUINO UNO

PIN11 or D4 to PIN7 of ARDUINO UNO

PIN12 or D5 to PIN11 of ARDUINO UNO

PIN13 or D6 to PIN12 of ARDUINO UNO

PIN14 or D7 to PIN13 of ARDUINO UNO

 

The connections which are done for color sensor are given below:

VDD to +5V

GND to GROUND

OE (output Enable) to GND

S0 to UNO pin 2

S1 to UNO pin 3

S2 to UNO pin 4

S3 to UNO pin 5

OUT to UNO pin 10

Arduino Based Color Sensor Circuit

The color which needs to be sensed by the color sensor is selected by two pins S2 and S3. With these two pins logic control we can tell sensor which color light intensity is to be measured.

Say we need to sense the RED color intensity we need to set both pins to LOW. Once that is done the sensor detects the intensity and sends the value to the control system inside the module.

S2

S3

Photodiode Type

L

L

Red

L

H

Blue

H

L

Clear (no filter)

H

H

Green

The control system inside the module is shown in figure. The light intensity measured by array is sent to current to frequency converter. What it does is, it puts out a square wave whose frequency is in relation to current sent by ARRAY.

Photodiode Array

So we have a system which sends out a square wave whose frequency depends on light intensity of color which is selected by S2 and S3.

 

The signal frequency sent by module can be modulated depending on use. We can change the output signal frequency bandwidth.

S0

S1

Output Frequency Scaling (f0)

L

L

Power Down

L

H

2%

H

L

20%

H

H

100%

The frequency scaling is done by two bits S0 and S1. For convenience we are going to limit the frequency scaling to 20%. This is done by setting S0 to high and S1 to LOW. This feature comes in handy when we are using the module on system with low clock.

 

The Array sensitivity to color is shown in below figure.

Array Sensitivity

Although different colors have different sensitivity, for a normal use it won’t make much difference.

The UNO here send signal to module to detect colors and the data received by the module is shown in the 16*2 LCD connected to it.

The UNO detects three color intensities separately and shows them on LCD.

The Uno can detect the signal pulse duration by which we can get the frequency of square wave sent by module. With the frequency at hand we can match it with color on sensor.

  1. Int frequency = pulseIn(10, LOW);

 

As by above condition the UNO reads pulse duration on 10th pin of UNO and stores it value in “frequency” integer.

We are going to do this for all three colors for color recognition. All three color intensities are shown by frequencies on 16x2 LCD.

Code

int OutPut= 10;//naming pin10 of uno as output

unsigned int frequency = 0;

 

#include <LiquidCrystal.h>

// initialize the library with the numbers of the interface pins

LiquidCrystal lcd(8, 9, 7, 11, 12, 13);//RS,EN,D4,D5,D6,D7

 

void setup()

{

                // set up the LCD's number of columns and rows

                lcd.begin(16, 2);

 

                pinMode(2, OUTPUT);

                pinMode(3, OUTPUT);//PINS 2, 3,4,5 as OUTPUT

                pinMode(4, OUTPUT);

                pinMode(5, OUTPUT);

                pinMode(10, INPUT);//PIN 10 as input

 

                digitalWrite(2,HIGH);

                digitalWrite(3,LOW);//setting frequency selection to 20%

}

void loop()

{

                lcd.print("R=");//printing name

                digitalWrite(4,LOW);

                digitalWrite(5,LOW);//setting for RED color sensor

                frequency = pulseIn(OutPut, LOW);//reading frequency

                lcd.print(frequency);//printing RED color frequency

                lcd.print("  ");

                lcd.setCursor(7, 0);//moving courser to position 7

                delay(500);

               

               lcd.print("B=");// printing name

                digitalWrite(4,LOW);

                digitalWrite(5,HIGH);// setting for BLUE color sensor

                frequency = pulseIn(OutPut, LOW);// reading frequency

                lcd.print(frequency);// printing BLUE color frequency

                lcd.print("  ");

                lcd.setCursor(0, 1);

                delay(500);

               

               lcd.print("G=");// printing name

                digitalWrite(4,HIGH);

                digitalWrite(5,HIGH);// setting for GREEN color sensor

                frequency = pulseIn(OutPut, LOW);// reading frequency

                lcd.print(frequency);// printing GREEN color frequency

                lcd.print("    ");

                lcd.setCursor(0, 0);

                delay(500);        

}              

Video

Have any question realated to this Article?

Ask Our Community Members

Comments

Submitted by Dany on Wed, 12/09/2015 - 01:33

Permalink

Please Do you have more photos of this project? thanks

Submitted by Yaakub on Sat, 12/19/2015 - 08:10

Permalink

Hi,

I need to understand better how you derive the "Output Frequency Scaling"; for example how you set 2% on S0 = H, S1 = L and the rest.

Please advise.

Thanks and best regards,

Submitted by Pen on Tue, 02/23/2016 - 01:57

Permalink

Will this code work for other models of colour sensor? I use the Adafruit TCS34725 and I'm constructing a colour sensor module with an LCD screen.

Submitted by Dionet on Thu, 07/07/2016 - 23:53

Permalink

hi, with which tools can i detected all the colors? not just the RGB, and i cant understand the code to modify

Submitted by Shashi on Sat, 08/06/2016 - 20:35

Permalink

I just bought a TCS 3200 and there is a S0..S4 pins on one end, and on the other end
5V,
GND
LED
OUT
pins - but I dont see a OE pin on my board !
I suspect that the LED pin is the OE ? Is this about right ?
Shashi

Submitted by pol on Tue, 10/04/2016 - 09:55

Permalink

What do you mean by that being a programmable sensor? Do we have to set the sensor when detecting a specific color?

Submitted by pius on Fri, 10/14/2016 - 15:44

Permalink

Sory.
Can you send to me full tutorial iniordel to lean it more.plz

Submitted by Dave P. on Fri, 01/20/2017 - 20:22

Permalink

The code line,

pulseIn(OutPut, LOW);//reading frequency

Is "pulseIn()" a function from a library that needs to be brought into the Arduino IDE, or is it an intrinsic in the C# language set supported natively?

Thanks for your example and code, this is great.

Submitted by Dave P. on Fri, 01/20/2017 - 20:26

Permalink

I looked on stackoverflow.com which has a lot of great arduino info, and believe I have confirmed that indeed PulseIn() is part of the C# implementation.

Submitted by Anas Masood Quddusi on Fri, 02/10/2017 - 06:42

Permalink

Hi, this tutorial was extremely helpful and I cannot thank you enough.
I want to take it a step further. Can we add a RGB LED somewhere and ask it to generate the same color as the one detected by the sensor?
So in short, Color X---> Sensor ---> Arduino ---> RGB LED ---> Color X.

Submitted by Atheeth on Fri, 02/17/2017 - 23:35

Permalink

Can it detect only three colours, if no pls tell the modifications to do so that we can detect more than 3 colours.

Submitted by Deepak on Sat, 03/18/2017 - 13:38

Permalink

Hello Dilip,

I have made this project. However, I find that all three values (R,G and B) are very close to each other, irrespective of what colour object is held up in front of the sensor. For example, without any object, I get R=188, B=183 & G= 190. Then when I bring a red object close to the sensor, it shows R=610, B=605 and G=620. With a blue object, I get R =676, B=670 and G = 690. Same is the case with a green object.

Can you tell me what I am doing wrong?

Thanks.

Deepak

Submitted by Soma on Sun, 04/22/2018 - 13:05

Permalink

Hi !, Thanks for this. here, when we measure visually red colour thing, lcd shows higher 'G' value than 'R' value & so on .How to avoid this problem ? It is a problem of tcs 3200 sensor , what is the suitable sensor ?
Thanks. Soma.

hello sir
can you help me to be able to get a Library (LIB) color sensor for Proteus Graphs
I really need it now
thank you..