Simple Metal Detector Circuit

Published  May 14, 2015   65
User Avatar Dilip Raja
Author
Simple Metal Detector Project using 555 Timer IC
Simple Metal Detector Project using 555 Timer IC

You can find a metal detector at airports, theaters and various other public places. They are used for the safety of people to detect anyone carrying a metal (Arms etc). In this project we are going to design a simple metal detector circuit. There are so many metal detector designs but most of them are complex in design so here we are going to design a simple metal detector circuit using 555 Timer IC.

Before going further we need to understand concept of inductor and RLC circuits. Let us first talk about inductors. Inductors are nothing but coils of enameled copper wire comes in different shapes and sizes. Based on various parameters the inductance of an inductor is calculated. In all of those parameters we are basically interested in core on the inductor as depending on the core, inductance value changes drastically.

In the figure below you can see the air cored inductors, In these inductors there will be no solid core. They are basically coils left in air. The medium of flow of magnetic field generated by inductor is nothing or air. These inductors have inductances of very less value.

Air Cored Inductors

These inductors are used when the need for values of few micro Henry. For values greater than few milli these are not a suitable one. In below figure you can see a inductors of ferrite core ,

Ferrite Core Inductors

When inductor coil is wound on a core may be ferrite or an iron core, the inductance of the coil increases enormously. This value is much more than the air cored one of the same size and shape.

Now for a RLC circuit as shown in figure, the reactance or impedance between terminals “a” and “c” depends on the values of L and C if the applied signal frequency is constant.

RLC Circuit

So if the inductance value changes the value of reactance or impedance changes. How these two concepts are used together for a metal detector circuit, is explained in working section of this project.

Metal Detector Circuit Components

  • +9 supply voltage
  • 555 IC
  • 47KΩ resistor
  • 2.2µF capacitor (2 pieces)
  • Speaker (8Ω)
  • 170Turns of 10cm diameter coil (any gauge would work)

Metal Detector Circuit Diagram and Working

Simple Metal Detector Circuit Diagram

The figure shows the circuit diagram of metal detector. The 555 IC timer here acts as a square wave generator and it generate pulses with frequencies audible to human. The capacitor between pin2 and pin1 should not be changed as it is need to generate audible frequencies. 

In the circuit there is an RLC circuit formed by 47K resistor, 2.2µF capacitor, and 150turn inductor. This RLC circuit is the metal detection part. Now as mentioned earlier in previous section, a metal core inductor has a high inductance value over a air cored one.

Remember the coil wound here is a air cored one, so when a metal piece is brought near the coil, the metal piece acts as a core for the air cored inductor. By this metal acting as a core, the inductance of the coil changes or increases considerably. With this sudden increase in inductance of coil the overall reactance or impedance of the RLC circuit changes by a considerable amount when compared without the metal piece.                  

At first when there is no metal piece the signal fed to speaker causes some audible sound. Now with the reactance change around the RLC circuit the signal sent to speaker will no longer be the same as before, because of this the sound produced by the speaker will be of different to the first one.                                

So whenever a metal is brought near the coil, the impedance of RLC changes making the signal to change resulting in variation to sound generated in speaker. You can also check this Arduino based metal detector.

Common Tips:

  • Enamel should be removed at the tips of coil for soldering connections.
  • With different gauge we will have different RLC impedance, so one should experiment with resistance in RLC circuit for sensitive metal detection.
  • The speaker can be of any type. But with resistance less than 8Ω, the timer might get heated.
  • Use supply voltage higher than 5V.
Video

Have any question realated to this Article?

Ask Our Community Members

Comments

Commented by on | Permalink

can weuse 10 mf capacitor instead of 2.2 mf capacitor

i neded circuit board the detector and
the real value of capacitors 2,2 mf o 2,2 nano? thanks very

Commented by on | Permalink

It really works because i have made this circui & it works perfectly.
What to do to increase it's sencitivity so that it can be used in various industries?

Commented by on | Permalink

Can I change the speaker to motor or solenoid?

Commented by on | Permalink

It's nice but the speaker turns always on.
It will be fine if the speaker turns off when there are no metal near inductor (coil)
and the speaker Turns on when a metal brought near inductor .
how can I do that?

Commented by on | Permalink

can you tell me the reason and explain the jop of every component of the circuit please ??

Commented by on | Permalink

Can u help me out with design Steps? How to choose the values of R, L, C and inductance?

Commented by on | Permalink

I now understand the concept behind metal detectors.

Thank you.

Commented by on | Permalink

i want to make door frame metal detector. Can anyone help me?

Commented by on | Permalink

its works better on alominom
its awsooome to make

Commented by on | Permalink

i need help to design turn off speaker when they is no metal found.. please help me to design..

Commented by on | Permalink

plz lets us know about theoritical design about this project

Commented by on | Permalink

I didn't connect this circuit, although I have question: does the voltage across the buzzer changes if a metal is brought near the coil?

Commented by on | Permalink

i have 2 cd player and 1 9volt battery and headphone...can you help me make a metal detector

Commented by on | Permalink

What transformer should be used so that it connects directly in the power source?

Commented by on | Permalink

nice mister anyway can u give us the video of how it works
thanks

Commented by on | Permalink

can i use the coil of 5 cm diameter

Commented by on | Permalink

please can you explain to what causes the continous noise or sound in the speaker.. need the answer as this a likely question in my project defense

Commented by on | Permalink

i need detail about this project

Commented by on | Permalink

what is the Detecting distance ?
and if i want to increase it , what I can do.

Commented by on | Permalink

the speaker doesnt make any sound what wud be the problem pls help urgent

Commented by on | Permalink

is it 150 turns or 170? wat xactly?

Commented by on | Permalink

made circuit using 2.2uf50v 10uf50v capacitors 47k resistor ne555 ic 8ohm speaker on coil i used 0.1mm enameled wire 150turns of120mm diameter . the detactor produces a high pitch sound which does not change even when coil is swept over a metal object. pliz help with specific voltages of capacitors and specific resistance of search coil

Commented by on | Permalink

I WANT TO MAKE METAL DETECTOR WHICH DETECT METAL FOR 10 FEET DOWN THE EARTH PLZ HELP ME

Commented by on | Permalink

What is the function of 10 micro farad capacitor here...??

Commented by on | Permalink

I m doing this project in my collage

Commented by on | Permalink

the 555 timer either sourcing or sinking a fixed amount of current from its pin 3,
so I see as the output is a fixed squarawave tone so the increasing of L coil will increase voltage on it that increasing current draining from pin 3 hence reducing tone....very simple ! I will build the circuit and examine it under oscilloscope and if there is time I will publish results here ...god willing...

Commented by on | Permalink

I used all the above components but the circuit is not working.

Commented by on | Permalink

can it detect all types of metal or only iron metal?? plz tell...

Commented by on | Permalink

Why there is a continuous sound occuring.can i know the reason

Because 555 timer is generating a square wave which is causing the sound and bringing metal near to it will change the frequency of that square wave hence the sound will also change.

Commented by on | Permalink

How can we find the frequency generated by IC in this circuit? Please inform me because I'm in great need of it.

Commented by on | Permalink

Can anyone tell me how much does each components cost?

Commented by on | Permalink

Whats are the voltage of capacitor

Commented by on | Permalink

I can't find inductance in my country
My country stops import it
What should I do?

Commented by on | Permalink

I am a hobbyist of metal detecting.
Can this metal detector circuit detect all kinds of metal?
There might be large functional difference.

Commented by on | Permalink

Hallo friend i like to learn this metal please send me all project until final thanks

Commented by on | Permalink

Could we replace the speaker with and LED instead?

Commented by on | Permalink

C
an we just use the normal copper wire..?

Commented by on | Permalink

in this circuit diagram pin 2 and pin 6 are connected.I think its only astable multivibrator. am i right sir ??can we design a metal detector using monostable multivibrator configuration where pin 6and pin7 are connected???

Commented by on | Permalink

What is the use of the 10 micro farad capacitor?

Commented by on | Permalink

what is the purpose of the 10uF capacitor in the circuit

Its a smoothing capacitor to filter noise. It is optional and hence you can ignore it if you cannot find a 10u cap

Commented by on | Permalink

Thank you....bro
it has done

Commented by on | Permalink

I made the exact same circuit. The coil of 170 turns, 22 gauge copper wire, 10 cm diameter and all the other components were kept the same as mentioned, but it did not work. I've tried it multiple times but not even the slightest of change in noise occurs.
Help me out. What could be the probable mistake?

Hey, did you figure out the same mistake because the same issue i'm also having.
Even i couldn't get the output.
I have coil of 500 turns remaining all specs are same.

Commented by on | Permalink

How thick should be the copper wire

Commented by on | Permalink

I want advantages of this project

Thanks for sharing this project. I was able to make a working copy with the specified components. I'm wondering if it would be possible to filter out the constant tone when no metal is near the coil by simply adding a basic RLC band stop filter between the output and the speaker. It would probably need to be a sufficiently high order one to retain the sensitivity, and band stop because both higher and lower frequencies should be able to pass (to detect both ferromagnetic e.g. iron and non-ferromagnetic e.g. aluminium). Please comment if you have tried something like this :) Also would be interested if someone had experimented with differently shaped coils (for example '8'-shaped) to improve the detection range.

Add New Comment

Login to Comment Sign in with Google Log in with Facebook Sign in with GitHub