GPS is a very useful device which is used in many electronics projects and applications like vehicle tracking system, GPS Clock, Accident Detection Alert System, traffic navigation and surveillance system etc. But question is how to use the GPS and read the data from GPS? We can easily get the GPS data directly into our computer using Arduino.
GPS stands for Global Positioning System and used to detect the Latitude and Longitude of any location on the Earth, with exact UTC time (Universal Time Coordinated). This device receives the coordinates from the satellite for each and every second, with time and date. GPS offers great accuracy and also provides other data besides position coordinates, we will into look it shortly.
In this arduino GPS tutorial, we are going to explain that how to Test or Interface GPS module using Computer and Arduino. For interfacing GSM with computer we either need USB to Serial Converter or Arduino Board. Here we are using Arduino board to interface GPS. We only need Arduino Board, GPS module, computer and 12v/3.3v adaptor for power supply. Here we have used GPS receiver Module SKG13BL (shown in above figure).
Before connecting it to the computer, we first need to remove the Arduino IC (Atmega chip) from the Arduino Board, as we only need the serial circuitry of the Arduino. This is called the Gateway mode. Removing the IC is shown in below figures:
Now do the connection like given in below picture:
- GPS TX pin to Digital PIN 1 of Arduino (TXD)
- GPS Ground Pin to GND PIN of Arduino
- GPS Power (3.3v) Pin to 3.3v PIN of Arduino
After connections, connect the USB cable to the computer, open your Arduino IDE software in computer, select com port and open serial monitor to listen the serial port and Power up the Arduino and GPS module.
Now you will see GPS data on Arduino Serial Monitor Window like below. Below are two snapshots, first one is, when GPS is not in range and second one is, when GPS in range.
GPS Data When GPS Receiver is out of range:
GPS Data When GPS Receiver is in Range:
In serial Window, you can see some sentences that start from $ sign. These are NMEA sentences. GPS module sends the Real time tracking position data in NMEA format (see the screenshot above). NMEA format consist several sentences, in which four important sentences are given below. More detail about the NMEA sentence and its data format can be found here.
- $GPGGA: Global Positioning System Fix Data
- $GPGSV: GPS satellites in view
- $GPGSA: GPS DOP and active satellites
- $GPRMC: Recommended minimum specific GPS/Transit data
These strings contain many GPS parameters like: Time, Date, Longitude, Latitude, speed, no. of satellites in used, altitude and many other things.
For any location coordinates and time, we can use $GPGGA and $GPRMC.
For Date and time we can use $GPRMC string.
When we use GPS module for tracking any location, we only need coordinates and we can find this in $GPGGA string. Only $GPGGA (Global Positioning System Fix Data) String is mostly used in programs and other strings are ignored. This string consist fix data as below:
$GPGGA,104534.000,7791.0381,N,06727.4434,E,1,08,0.9,510.4,M,43.9,M,,*47 $GPGGA,HHMMSS.SSS,latitude,N,longitude,E,FQ,NOS,HDP,altitude,M,height,M,,checksum data
|
Identifier |
Description |
|
$GPGGA |
Global Positioning system fix data |
|
HHMMSS.SSS |
Time in hour minute seconds and milliseconds format. |
|
Latitude |
Latitude (Coordinate) |
|
N |
Direction N=North, S=South |
|
Longitude |
Longitude(Coordinate) |
|
E |
Direction E= East, W=West |
|
FQ |
Fix Quality Data |
|
NOS |
No. of Satellites being Used |
|
HDP |
Horizontal Dilution of Precision |
|
Altitude |
Altitude (meters above from sea level) |
|
M |
Meter |
|
Height |
Height |
|
Checksum |
Checksum Data |
And $GPRMC string mainly contains velocity, time, date and position
$GPRMC,123519.000,A, 7791.0381,N, 06727.4434,E,022.4,084.4,230394,003.1,W*6A $GPRMC,HHMMSS.SSS,A,latitude,N,longitude,E,speed,angle,date,MV,W,CMD
|
Identifier |
Description |
|
RMC |
Recommended Minimum sentence C |
|
HHMMSS.SSS |
Time in hour minute seconds and milliseconds format. |
|
A |
Status // A=active and V= void |
|
Latitude |
Latitude 49 deg. 16.45 min. North |
|
N |
Direction N=North, S=South |
|
Longitude |
Longitude(Coordinate) |
|
E |
Direction E= East, W=West |
|
Speed |
speed in knots |
|
Angle |
Tracking angle in degrees |
|
Date |
Time stamp (Date in UTC) |
|
MV |
Magnetic Variation |
|
W |
Direction of variation E/W |
|
CMD (*6A) |
Checksum Data |
Mostly this string is used for taking time, date and speed.
Comments
Very good..
Very good..
yes you can upload a blank program or led blinking program.
Thank you for uploading this
Thank you for uploading this vedio. I have done this, now i want to extract only gprmc code and with 5 minutes interval.
Please help me to finish my project.
You need to change the
You need to change the frequency or put in a loop with a five minute delay..
Better to leave frequency alone for better result and just show the result every five seconds
Its already mentioned that we
Its already mentioned that we only need the serial circuitry of the Arduino. This is called the Gateway mode.
what will happen if u dont
what will happen if u dont remove the IC?
Error problem
I done the same connection as you did and open the arduino IDE and serial monitor but i didn't get any data like your output.But i get some garbage output .Now what i do??? Help me as soon as possible
Follow the complete procedure
Follow the complete procedure carefully.
hello selvakumar, please
hello selvakumar, please check the baud rate in the code and set the same baud rate in arduino serial monitor.
Arduino GPS tracker
Hi, I am doing my final year project "Real Time Arduino Vehicle Tracker",
1. Why didn't you install a GPS Shield instead of a GPS Receiver?
2. What are the difference between these two components?
3. Do we really need an internal + an external GPS antennas if we use a GPS shield?
4. Did you insert a SIM CARD to your GPS Receiver?
Your help would be greatly appreciated. :)
Answer to your questions:
Answer to your questions:
1. You can use GPS shield with Arduino, it will be better.
2. GPS shield is specifically for Arduino and can be fit on it easily whereas GPS receiver can be used with any microcontroller.
3. Antenna will depend upon your GPS module, some module have it and some dont.
4. No, SIM isn't inserted in GPS module.
gps is not showing status led
in the serial monitor i can see that gps is sending the nmea formatted string with out lat and long values
and even the status led of gps is not blinking
@ganapathi and @Ajay: If you
@ganapathi and @Ajay: If you are getting NMEA string without Long and Lat, that means your GPS module is not in range. Try placing the antenna in open sky and also provide proper power supply to it, it has two options for power supply 3v or 12v, set it correctly.
GPS longitudes and latitudes as variable
How to get GPS longitudes and latitudes as variable from arduino kit, further i can use this variable in other purpopse.
your help would be greatly appreciate!
how to choose gps module for
how to choose gps module for our preferred arduino?
shall we use any arduino
shall we use any arduino model with any gps?/
Yes, but you should check
Yes, but you should check datasheet of GPS before connections.
Arduino interfacing with gps
my project is " Smart helmate and accident detection''. In that first i detect accident happened or not, if yes then send location to nearest hospital and any one of his/her friend or family. The problem is I don't know how to do. i'm getting continuous data in serial monitor, i need specific coordinates of location and to send that msg to hospital and friend im using gsm kit with arduino. Please if u help me in this it will be great to me.
In the serial monitor, I'm
In the serial monitor, I'm getting a single line output which consists of one NMEA string. How do i get multiple NMEA strings as shown in the video?
Data Always out of range
Whatever I do the GPS data seems to be always out of range :(
My gps receiver sim28m is
My gps receiver sim28m is always out of range. How to bring it into range?
How can I display only the
How can I display only the longitude and latitude data? I only need the two and Im using sim808 gprs/gsm+gps shield v1.1.
Thank you in advance.
Can u give the Code for this
Can u give the Code for this project?
gps
sir i used the gps28ml module and i connected it as per your connections but i didn't get any values on my serial monitor.is there any process to test my gps28ml module?
how much voltage i should give to my gps28ml ? i directly connected 5v from my Arduino.is there any problem?
I had seen a project 'arduino
I had seen a project 'arduino based automatic vehicle accident detection and reporting system using GSM and GPS. Thatswhy i choose this project as my final year project and i assembled it with the preferred components. But now i cant access the latitude and longitudinal values from the gps module , the execution of the program still remains by showing "getting gps data please wait" . Can u pls help me as possible as earlier. ...
I am. Doing my final year
I am. Doing my final year project but I am not getting anything on serial monitor so I need help sir pls help me
gps module to arduinouno
i couldn't find the code for gps module to receive latitude and longitude. can anyone send it to me?
In place of removing the IC on arduino, we can upload a blank program i.e. with a blank setup() and blank loop()....